Intel GA-8IPXDR-E Manuale Utente

USER’S MANUALGA-8IPXDR-E Series Intel® Dual XeonTM ServerboardIntel® Dual Xeon Processor ServerboardRev. 100125A08-08IPX-F00

10GA-8IPXDR-E(C) MotherboardStep 1: Install the Central Processing Unit (CPU)Step 1-1: Installing Motherboard to the Chassis...You may use the 4 screw

Hardware Installation Process11Step 1-2: CPU InstallationPin1 indicatorCPU Top View: Socket 603 / 400MHz1. Pull the lever out, than lift up the Lever.

12GA-8IPXDR-E(C) Motherboard00000 Please make sure the CPU type is supported by the motherboard.00000 If you do not match the CPU socket Pin 1 and C

Hardware Installation Process13Step 1-3: CPU Heat Sink Installation1. Use qualified fan approved by Intel.3. First step of assembling.2. Heat Sink5. S

14GA-8IPXDR-E(C) Motherboard00000 Please use Intel approved cooling fan.00000 We recommend you to apply the thermal paste to provide better heatconduc

Hardware Installation Process15Step 2: Install memory modulesThe motherboard has 6 dual inline memory module (DIMM) sockets, but it can only support a

16GA-8IPXDR-E(C) MotherboardInstallation Step:1. The DIMM slot has a notch, so the DIMMmemory module can only fit in one direction.2. Insert the DIMM

Hardware Installation Process17Step 3: Install expansion cards1. Read the related expansion card’s instruction document before install the expansion c

18GA-8IPXDR-E(C) MotherboardStep 4: Connect ribbon cables, cabinet wires, and powersupplyStep 4-1: I/O Back Panel IntroductionXXXXX PS/2 Keyboard and

Hardware Installation Process19ZZZZZParallel Port / Serial Port / VGA Port (LPT/COMA/VGA)¾This connector supports 1 standard COM port,1 Parallel port

2GA-8IPXDR-E(C) MotherboardTable of ContentItem Checklist ...4GA

20GA-8IPXDR-E(C) MotherboardStep 4-2: Connectors IntroductionA) ATX3 L) COM2B) ATX1 M) CASEOPENC) ATX2 N) J20 (Front Panel)D) BT1 O) J30E) SCSI1 P) J3

Connector Introduction21 A) ATX3 (2x12 Pin ATX Power ) B) ATX1 (ATX1 Power )¾This connector (ATX +12V) is used only forCPU Core Voltage.124Pin No. Def

22GA-8IPXDR-E(C) Motherboard C) ATX2 (+12V Power Connector)¾This connector (ATX +12V) is used only forCPU Core Voltage.Pin No. Definition1 GND2 GND3 +

Connector Introduction23 F/O) J33/J34 (System FAN Connector) P) J31 (Power FAN Connector)Pin No. Definition1 GND2 +12v/Control3 Sense1J331J34Pin No. D

24GA-8IPXDR-E(C) Motherboard L) COM 2 Connector T) J18 (Wake On LAN Connector)1Pin No. Definition1 +5VSB2 GND3 SignalPin No. Definition1 NDCDB2 NSINB3

Connector Introduction25 E/F) SCSI1/2 ConnectorSCSI 1SCSI 2 I/J) IDE1/IDE2 [IDE1 / IDE2 Connector(Primary/Secondary)]¾Important Notice:Please connect

26GA-8IPXDR-E(C) Motherboard M) CASE OPEN G) FDD1 (Floppy Connector)Pin No. Definition1 Signal2 GND1Floppy123433

27GA-8IPXDR-E(C) Motherboard N) J20 (Front Panel Connector-- Power button and Power LED)Pin No. Definition17 PWR LED+18 PWR LED-19 PWR BTN+20 PWR BTN-

28GA-8IPXDR-E(C) Motherboard D) BT1 (Battery)CAUTION Danger of explosion if battery is incorrectlyreplaced. Replace only with the same or equivalent

Connector Introduction29JP_RSTJP_SPK-JP_HD+JP_HD-JP_SPK+JP_RST (Reset Button) Open: Normal OperationClose: Reset hardware systemJP_HD (HDD Active LED)

3Table of ContentChapter 4 Technical Reference ...60GA-8IPXDR-E System Block Diagram...

30GA-8IPXDR-E(C) MotherboardStep 4-3: Jumper Setting Introduction1) JP 1 9) JP 172) JP 8 10) JP 183) JP 9 11) JP 194) JP 10 12) JP 205) JP 13 13) JP 2

31Jumper Setting 1) JP 1 (Onboard SCSI Function) 2) JP 8 (Onboard VGA Functon) 3) JP 9 (Front Side USB Wake Up Function)1-2 close: VGA Enabled (Def

32GA-8IPXDR-E(C) Motherboard5 / 6) JP13 / JP14 (P64H2#1 Primary PCI-X max Bus Frequency Function) For PCI-X_11 4) JP 10 (Rear Side USB Wake Up

33Jumper Setting7 / 8) JP15 / JP16 (P64H2#1 Secondary PCI-X max Bus Frequency Selection) For Giagbit LAN U6JP15 : JP16 = 1-2 closed ; 1-2 closed=

34GA-8IPXDR-E(C) Motherboard11 / 12) JP19 / JP20 (P64H2#2 Secondary PCI-X max Bus Frequency Selection) For PCI-X_2 and PCI-X_4JP19JP20JP20 : JP

35Jumper Setting1-2 close: Clear CMOS2-3 close: Normal (Default)11 You may clear the CMOS data to its default values by this jumper 15) CLR_CMOS (Cl

GA-8IPXDR-E(C) Motherboard36<Ç> Move to previous item<È> Move to next item<Å> Move to the item in the left hand<Æ> Move to the

BIOS Setup37zzzzz MainThis setup page includes all the items in standard compatible BIOS.zzzzz AdvancedThis setup page includes all the items of AMI s

GA-8IPXDR-E(C) Motherboard38 System Date Set the System Date. Note that the “Day” automatically changed after you set the date. (Weekend: DD: MM:

BIOS Setup39 Floppy Drive A/B This category identifies the type of floppy disk drive A or drive B that have been installed in thecomputer.

4GA-8IPXDR-E(C) Motherboard; The GA-8IPXDR-E series motherboard ; I/O Back Panel; IDE cable x 1/ Floppy cable x 1 ; USB Cable x 1(Optional); Driver C

GA-8IPXDR-E(C) Motherboard40Fast Programmed I/O Mode This field only shows the information of Fast Programmed I/O Mode.32 Bit Transfer Mode Enables

BIOS Setup41AdvancedFigure 2: Advanced***** About This Section: Advanced This section “Advanced” will be divided into five sub-menus. Advanc

GA-8IPXDR-E(C) Motherboard42Advanced Configuration Advanced Configuration` Quick BootThis setting allows BIOS to skip certain tests while booting

BIOS Setup43` MPS Version for O.SThis option allows a user to select MP (Multi Processors) system supported version.Note: Some old MPS OS support 1.1

GA-8IPXDR-E(C) Motherboard44Figure 2-2: Chipset ConfigurationChipset Configuration Chipset Configuration` ClkGen Spread SpectrumEnabled Enable C

BIOS Setup45AMI BIOS NEW SETUP Utility - VERSION 3.31a Main Advanced Security Boot ExitPower Management Configuratio

GA-8IPXDR-E(C) Motherboard46AMI BIOS NEW SETUP Utility - VERSION 3.31a Main Advanced Security Boot ExitPCI-X Config

BIOS Setup47Peripheral ConfigurationFigure 2-5: Peripheral Configuration Peripheral Configuration` OnBoard IDEOption: Both (Default Value), Pri

GA-8IPXDR-E(C) Motherboard48` OnBoard Serial Port A This option specifies the base I/O port address of serial prot A.3F8/COM1 Enable onboard serial

BIOS Setup49` Parallel Port Mode This option specifies the parallel mode.Normal The normal parallel pro is used.Bi-Directional Use this setting to

5WARNING!If the motherboard has mounting holes, but they don’t line up with the holes on the base and there areno slots to attach the spacers, do not

GA-8IPXDR-E(C) Motherboard50` OnBoard Gigabit LANsThis option allows user to function onboard Gigabit LANs.Enable Enables onboard Gigabit LANs. (Defa

BIOS Setup51AMI BIOS NEW SETUP Utility - VERSION 3.31a Main Advanced Security Boot ExitHardware Configuration [Setup

GA-8IPXDR-E(C) Motherboard52 Hardware Monitor ConfigurationThis section provides the system hardware health information to user for reference.` R

BIOS Setup53` CPU 0 / 1 FANThis field indicates the RPM (Ratio Per Minute) of current CPU 0/1 speed.` System FAN 1This field indicates the RPM (Ratio

GA-8IPXDR-E(C) Motherboard54SecurityFigure 3: SecurityAMI BIOS NEW SETUP Utility - VERSION 3.31aMain Advanced Security Boot

BIOS Setup55Set User PasswordYou can only enter but do not have the right to change the options of the setup menus. Whenyou select this function,

GA-8IPXDR-E(C) Motherboard56BootAMI BIOS NEW SETUP Utility - VERSION 3.31aMain Advanced Security Boot Exit[Setup Hel

BIOS Setup57` The Choice for 1st Boot Device: ,Removable Device (Default Value) ATAPI CDROMHard DiskDisabled.` The Choice for 2nd Boot Device:R

GA-8IPXDR-E(C) Motherboard58AMI BIOS NEW SETUP Utility - VERSION 3.31aMain Advanced Security Boot Exit[Setup Help]Ex

BIOS Setup59Exit Saving ChangesThis option allows user to exit system setup with saving the changes.Press <Enter> on this item to ask for t

6GA-8IPXDR-E(C) MotherboardForm Factor y 30.5cm x 33cm Extend ATX size form factor, 8 layers PCB.CPU y mPGA 604 socket for Intel® XeonTM processor w

GA-8IPXDR Motherboard60Revision HistoryChapter 4 Technical ReferenceGA-8IPXDR-E System Block Diagram

61AppendixRevision HistoryChapter 5 AppendixInsert the driver CD-title that came with your motherboard into your CD-ROM driver, the driverCD-title wil

GA-8IPXDR-E(C) Motherboard62(5)6. Ready to install the program.Click "Install" to begin theinstallation.(6)Starting installation(7)8. Wizard

63AppendixInsert the driver CD-title that came with your motherboard into your CD-ROM driver, the driverCD-title will auto start and show a series of

GA-8IPXDR-E(C) Motherboard64Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driverCD-title will auto start and

65AppendixInsert the driver CD-title that came with your motherboard into your CD-ROM driver, the driverCD-title will auto start and show the installa

GA-8IPXDR-E(C) Motherboard66Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driverCD-title will auto start and

67AppendixPin Definition Pin Definition1 EMP Port ENABLE 36 POWER BUTTON OUT2 5VSB 37 POWER BUTTON IN3 SERIAL PORT 38 SYSTEM S54 SERIAL PORT 39 SERIAL

GA-8IPXDR-E(C) Motherboard68Acronyms MeaningACPI Advanced Configuration and Power InterfaceAPM Advanced Power ManagementAGP Accelerated Graphics PortA

69AppendixLAN Local Area NetworkLBA Logical Block AddressingLED Light Emitting DiodeMHz MegahertzMIDI Musical Instrument Digital InterfaceMTH Memory T

7IntroductionHardware Monitor y CPU/Power/System Fan Revolution detecty CPU Overheat Warningy System Voltage DetectOn-Board LAN y Build in Intel 8254

GA-8IPXDR-E(C) Motherboard70Technical Support/RMA SheetCustomer/Country: Company: Phone No.:Contact Person: E-mail Add. :Model name/Lot Number: PCB re

8GA-8IPXDR-E(C) MotherboardGA-8IPXDR-E(C) Motherboard LayoutLPTATX1ATIRage XLBT1ATX3*SCSI7902WUSB1IDE2PCI_4CPU2CPU1 (Install First)604 PIN Socket604 P

Hardware Installation Process9To set up your computer, you must complete the following setups:Step 1- Install the Central Processing Unit (CPU)Step 2-